Conclusion lab report introduction to ac circuit analysis
Practical - lab report for experiment 4 lab report for experiment, typed, including introduction, methods, results and conclusion. Conclusion lab report introduction to ac circuit analysis lee 1 kwan woo lee lab report#1 measurements in resistive networks and circuit laws laboratory abstract: the purpose of this lab is to verify the ohm's law, kirchhoff's voltage and current laws as well as the introduction to the voltage division. Finally, run an ac analysis on this same circuit first, change the resistor r4 to a 1 mf capacitor (circuits with just resistors do not change as a function of frequency) type ac in the ac amplitude box in v1 set the simulation to run from 1 hz to 10 khz in a decade sweep with 10 points per decade, and plot the voltage across the capacitor paste the. Conclusion: in this lab we used the oscilloscope to measure the current of several simple circuits the oscilloscope let us actually see the current going through our setup and allowed us to manipulate it to acquire values and a different perceptive of this flowing energy through this lab we slowly figured out how to properly use this machine and. Science 14 lab 3 - dc circuits theory all dc circuit analysis (the determining of currents, voltages and resistances throughout a circuit) can be. Turn all equipment off and disconnect the circuit analysis: 1 use excel to produce a plot of frequency vs voltage set the frequency axis to a logarithmic scale to do this right click on the axis chose ‘format axis’ and check the box for ‘logarithmic scale’ 2 draw a smooth curve through all the data points this curve should be similar to figure 2.
Different then in part 2 where the transient analysis was invoked, in part 5 of the experiment an ac analysis (ac) were performed unlike the tran analysis the ac analysis does not involve differential equations in it's calculations rather the ac analysis uses the same approach as the hand calculations in part 1 this approach alleviates. Usually, the objectives mentioned in the introduction are examined to determined whether the experiment succeeded if the objectives were not met, you should analyze why the results were not as predicted note that in shorter reports or in reports where discussion is a separate section from results, you often do not have a. Physics 1140 spring 2005 e11 lab e1: introduction to circuits introduction the purpose of the this lab is to introduce you to some basic instrumentation used. 4 figure 44 circuit for ac steady state analysis as an example, let the input voltage be 100cos(2π60t + 30o)let r=100ω , l=025h , c=10µf we note that ω = 2π60 = 377. The dc power supply 4 connect the circuit in fig 5 and measure id, ic, il using the oscilloscope 3 filter circuit introduction to experiment f a low pass filter can be used to further reduce ripple as in fig 6. Dc circuit analysis object: the purpose of this lab is to understand how current distributes in a dc circuit of resistors apparatus: ac/dc electronics lab board, resistors, and multimeter introduction: when a circuit composed of resistors is connected to an emf device (battery), there are some simple rules that can be applied.
Introduction to report writing prerequisite: or concurrent: ee t 101 prerequisite: or concurrent: ee t 101 course goals: the purpose of this course is to learn the basic requirements for building simple dc/ac circuits students will employ power supplies as well as measure electrical parameters of current, voltage, resistance and impedance. P31220 lab 1 ohm’s law and dc circuits purpose: students will become familiar with dc potentiometers circuits and ohm’s law introduction: ohm’s law for electrical resistance, v = ir, states the relationship between current, voltage. Laboratory 1 introduction to the circuit laboratory this is the first laboratory where you will deal with such matters as the course objectives.
60 hz ac voltages used in fluorescent lights me lab report 0 505 from the circuit and measured a resistance of 3023 k was measured with a lg precision dm-441b. Circuits laboratory experiment 1 dc circuits – measurement and analysis 11 introduction in today's high technology world, the electrical engineer is. Introduction methods and materials (or equipment) experimental procedure results discussion conclusion references appendices further reading 1 the title page needs to contain the name of the experiment, the names of lab partners, and the date titles should be straightforward, informative, and less than ten words (ie not “lab.
Conclusion lab report introduction to ac circuit analysis
Introduction to circuits -lab report topics: resistor, ohm's law, electric current pages: 11 (1498 words) published: december 28, 2013 elec 202 lab 1 report. This chapter's topics are of practical importance in ac systems the fundamental terminologies used in ac circuits are introduced, and a number of custom-written vis, considering both single-phase and three-phase ac circuits, are provided.
Sample lab report - phys 231 the following is an example of a well-written report that might be submitted by a phys 231 student • the report begins with a short statement of what is being measured, and why. Report on lab 2 thévenin resistance and voltage of a power supply this report presents a measurement of the thévenin resistance and i introduction this report. Phys 102 formal simple dc circuits lab report 1 kaitlyn greiner formal lab report: title of experiment: simple dc circuits date performed: july 16th, 2014 lab partners: erin phlegar and stephen few physics 102l, section: 02 professor teklu abstract: in this lab, my objective was to understand the relationships between resistance, potential difference, and current in a simple circuit. Rlc circuit- no voltage source this rlc circuit [figure 1] proved to be an interesting demonstration of the current in a circuit without a voltage source the initial current running through the circuit is provided by the charged capacitor however, this initial current undergoes damping due to the resistor in place, and the current running.
Electric circuits laboratory manual (ece-235 lab) guide lines for the experiments and report preparation 1 preparation for the experiment: before conducting the. Conclusion for ac circuit lab report i've already done the lab report i only need the objective to be as a paragraph (own words), and the conclusion part to b. Supporting links: lab reports sample lab report #2 site links: writing guidelines writing exercises this web page presents a sample report [herwald, 1999] written in a microprocessor laboratory course at virginia tech. 1 elg2331: experiment 3 ac circuit analysis objective: to familiarize the students with ac circuit analysis and measurements including the.